- Symantec backup exec 2010 r3 linux agent install#
- Symantec backup exec 2010 r3 linux agent pro#
- Symantec backup exec 2010 r3 linux agent verification#
Test PART 1: CARVE OUT DISK FOR THE RALUS AGENT ON THE QNAP Log into the QNAP GUI and create a shared folder. untar the BE RALUS agent into those directories Alter QNAP system files to make the agent run.
Symantec backup exec 2010 r3 linux agent install#
Post if you do!) Symantec Backup Exec 2010 R3 (w/ original media and a Linux agent license available) General procedural outline: Create a directory on disk that will house the Backup exec agent on the QNAP Use a separate Linux system to download needed libraries Use said Linux system to install RALUS (Backup exec Linux agent) Gather up files into a tarball and move them to the QNAP.
Symantec backup exec 2010 r3 linux agent pro#
CentOS 6 32-bit (in a VM w/ an Internet connection) QNAP TS-439 Pro II+ (these steps have been vetted on no other platform. a sense of adventure (desperation may be substituted for this based upon severity of #1) Software/Equipment used. This guide is scarce on explanations and hand holding in general. root access to a Linux system, and a familiarity with the Linux/UNIX command line interface.
admin access to a QNAP with an Intel Processor. A lack of any way to accomplish your end goal with a supported solution. In fact, if you consider this entire article the ravings of a madman, that would probably be the smart thing. Future firmware updates may break some or all of these workarounds, resulting in this solution no longer functioning. The author makes no claims or guarantees, either express or implied, that these steps are complete, or safe, or fit for any purpose, whatsoever. The author takes no responsibility for any data loss or damage, direct or indirect, that may result from attempting the steps described in this article. Use of any instructions contained herein as at the reader's own risk. Please refer carefully to those documents and consider your actions carefully before attempting these steps. Warning and disclaimer: This is completely unsupported, and may void your warranty or break your license agreement.
We changed the alert to automatically clear after 1 minute and now the backups are finishing on their own.I've seen a lot of questions out there on this one, and I wanted to let people know that, in at least one case, it's possible to get a Backup Exec RALUS agent loaded and running on a QNAP. Do you guys have any ideas, thoughts, suggestions of what I should check, etc? Let me know if there's any more information I can supply.Īny help would be appreciated on this bizarre issue!ĮDIT: Thanks for the suggestions George and Pauska, but no dice unfortunately.ĮDIT #2: Solved! There was an alert that was requiring acknowledgement before it finished the job, but the alert never popped up when Backup Exec was open. I've been researching this issue, but without much luck so far. If you don't open the application, the job will stay in limbo indefinitely. It can sit at a backed up byte count of 1.8TB with the elapsed time spilling well past 12 hours, but as soon as you open Backup Exec the job will change its status to 'Successful' within 15 minutes (and subsequently eject the tape).
Symantec backup exec 2010 r3 linux agent verification#
The job rate stays around 3.2GB/min (on average, sometimes faster) and usually completes the backup and verification process in about 8.5 - 9 hours.īUT, the job only finishes if Backup Exec is open.
The scheduled task's properties look fine (permissions, selections, notifications, alerts, etc.) and it starts perfectly each night. For a more detailed description, what I mean is that the schedule runs perfectly fine. Here's the fun part Every day the backup 'waits' to be seen in order to finish. 5204, 64-bit).Įach night, we have a scheduled task to back up our main shares/drives/etc (roughly 1.8TB) to an IBM Ultrium-HH5 (LTO5) tape drive. On one of our main servers (a Poweredge R510 running Server 2008 R2 Standard SP1 Build 7601), we run Symantec Backup Exec 2010 R3 (Version 13.0 Rev.